Coil connector plug seals.

[trophydave]

Are the seals that sit inside the blue plugs that fit onto the coils available from anywhere?

[Dyn Blin]

the oval two holed black ones that fit into these?

[trophydave]

Yes,thats them.

[Dyn Blin]

I was afraid you'd say "yes". 

I looked for these a couple years ago after one popped out while I was changing plugs, and I never found it.  The clip and shape of the pins look Delphi, but I've never been able to source it.  I finally ended up cutting some spares from an old wet-suit. 

Unless someone else calls it out, I'll dig a bit and see if I have more success this time around.

[JoeDirt]

Are the seals that sit inside the blue plugs that fit onto the coils available from anywhere?

I popped one out of my old harness. I looked on BikeBandit.com here in the states and they show nothing except the whole wire harness. I took a picture so you can see what you are looking for:

[JoeDirt]

The clip and shape of the pins look Delphi, but I've never been able to source it.

Delphi 12033769B is very close to the one on our bikes. There is one for $6USD on US eBay.

It might be backwards after looking closer.

[Dyn Blin]

http://www.mouser.com/Search/ProductDetail.aspx?qs=FeDNFVUrI9WOoOTbDpCqtg%3d%3d

This looks pretty darn close

[JoeDirt]

http://www.mouser.com/Search/ProductDetail.aspx?qs=FeDNFVUrI9WOoOTbDpCqtg%3d%3d

This looks pretty darn close

Yea... I was looking at those also. You can get those for $.25 USD. It would be worth a try.

[Dyn Blin]

to beat a not-quite dead horse tiger:
When I resort for all Delphi 2 prong seals, there's only one that's black (the middle with no illustration).  Maybe I'll try one of each flavor and post back here

Edit:  Ordered one of each, (yeesh, the postage was more than the items)- I'll post back with photos here when they arrive in 4-10 days.

TrophyDave, if they work, I'll post one to you.

[KuzzinKenny]

Is this the one 

http://uk.rs-online.com/web/p/automotive-connector-accessories/6737953/

or one O these...........

http://uk.rs-online.com/web/c/connectors/power-connectors/automotive-connectors/#esid=4294957459&applied-dimensions=4294882771

KK

[John Stenhouse]

I think they're just looking for the seal not the whole connector

[trophydave]

Yes,just the seal,its the one in the picture posted by JoeDirt in reply number 4.I have one good seal,one is squashed out of shape and the other is missing.

[JoeDirt]

I bought a Delphi connector to replace my main fuse connector. It came with one of those seals mentioned above. I tried to squeeze it in the blue coil connector. It wasn't  a good fit... but may be possible with the right amount of determination. :icon_wink:

~JD

[trophydave]

Thanks for the replies.In the end I bought the cheapest 955 loom that I could find on ebay.It was off a Sprint ST but only because the Tiger ones were quite a bit more money.OK 15 quid might be a bit steep for a couple of rubber seals but there should be enough bits of wire and various other stuff to last me for years.

[Dyn Blin]

Edit:  Ordered one of each... I'll post back with photos here when they arrive in 4-10 days.

I returned from some travel for work today to find a Mouser envelope in the pile-o-post.  To close the loop, what follows is a poor pic of both items outlined in the catalogue screenshot above.  One item ( the one with no catalogue illustration) is a female side of a 2 prong connector that appears to be 1/2 of a water resistant assembly.  The seal that was what I was after is actually black, but appears to be the same as the connector in the Mod-man Dirt's pic. I haven't had an opportunity to pull the tank to see if it'll fit, but my guess is it's too big. 

The choice of cannibalizing a surplus harness seems to be a good one to resolve the issue.