News:

Welcome to the TigerTriple forum! Over the years we have gathered lots of great information on all things Triumph Tiger. Besides that, this is a great community that is willing to help you keep your Tiger moving. So, feel welcome! Also, try the search button for answers to your questions. If you have any questions, PM me on ghulst.

Main Menu

Surging at 3-4k RPM

Started by Flyingwombat, March 11, 2024, 07:52:00 PM

Previous topic - Next topic

Flyingwombat

Fixed 1601, the engine light lamp had come out of it's connection, easy fix.
2011 Triumph Street Triple - daily
1999 Triumph Tiger 885i - fun and free

the slow heart

If after each dismantling you find throttles bit off balance, you might be right to prime suspect worn screws.

When you blow with mouth at iacv, are all three lines equally releasing air? When you continue blowing and finger block orifices at manifold, do you feel pressure block and silence? O ring under the valve should be good.

What about the spark plugs?

ghulst

When you cleaned the carbs, did you really push something through all of the needles and thoroughly did the same with all of the other little passageways within the carbs?

I did an ultrasonic cleaning session on the carbs of my Ducati and then I needed to do it again. ;)
2008 Triumph Street Triple R | Ex Triumph Tiger 900 T400 1993, Tiger 800XC 2011

Flyingwombat

#18
Uploaded the latest map, no difference.

"If after each dismantling you find throttles bit off balance, you might be right to prime suspect worn screws."

Possible but threads look in good condition

"When you blow with mouth at iacv, are all three lines equally releasing air? When you continue blowing and finger block orifices at manifold, do you feel pressure block and silence? O ring under the valve should be good."

Oring appears fine, will blow into IACV to check...

"What about the spark plugs?"

 All new and gapped correctly.

"When you cleaned the carbs, did you really push something through all of the needles and thoroughly did the same with all of the other little passageways within the carbs?"

Used carb cleaner spray from liquimoly to clean throttle body inlets, will be ordering new seals for injectors, will clean the injectors and replace the seals when I do. Also trying to get an EFI relay, and a throttle body housing.
2011 Triumph Street Triple - daily
1999 Triumph Tiger 885i - fun and free

the slow heart

If the fuel map is updated and no test/sensor misbehave, the possibility of electrical issue gets less. Is there easy way to check that all three spark plugs fire at required frequency?

And since problem is in lower rpm some air leak still might cause the erratic situation. Injector seals renewal is a good move in that sense. You could think further which seals are exactly broken during your work, and how to check all of them for sure after the problem shows again ( since threads/screws seals are intact ). If you try to reproduce the problem with iacv socked unplugged from the el.looming, what happens?

Good luck!

Flyingwombat

So today I addressed a sticky throttle cable, not a cause. Then installed a new IACV housing and more rigid hoses, just in case.

I checked the balancing screws, they were annoyingly loose, I could turn them with my fingers on the heads... So will get some new loctite.

Got some throttle bodies from a broker, the screws were so much stiffer, so will re-balance with the new ones, came with injectors so will be cleaning them and selecting the best. Hopefully this will sort it. Otherwise fuel pump will be coming out, which is a bit of a pain I'd rather not have to work on.

2011 Triumph Street Triple - daily
1999 Triumph Tiger 885i - fun and free

Lee337

Big respect for sticking with this, many would have got shot of the bike by now.

Looking forward to seeing you resolve the issues & having a fully functioning bike.
No matter how smart you are you can never convince someone stupid that they are stupid.

Flyingwombat

Thanks, was my dad's bike so it's not just a bike. Also I'm an engineer, so I spend my whole life trying to work out why things are broken.

Today I cleaned the injectors and fuel rail.

Battery needs a charge before it'll start again, so fingers crossed tomorrow.

At this rate it'll be running next January...
2011 Triumph Street Triple - daily
1999 Triumph Tiger 885i - fun and free

Flyingwombat

Cleaning injectors did not help...

My long term fuel trim seems to have set itself really weird too, was down at -60, I have tried to reset this, but unfortunately the slider on the TuneECU app is playing up (only for the trim) and if I select any number highlighted it jumps to another random number, ie. -10 jumps to +80 and then 0 to -80 and +10 to +60. Doesn't make sense so have a TuneECU query on this as it seems to be a UI issue on the app.

The engine is quite sporadic now, it's fluctuations have worsened, at idle it will stall or bring itself up to around 3000rpm.

On the plus side I think I'm getting there. The fuel pump is noise when priming is getting worse, a very noticeable squeal now. Considering replacing that, the fuel pressure regulator and the filter. Could do with measuring the fuel pressure really but the Triumph part is extortionate. Does anyone know how to read the pump voltage?
2011 Triumph Street Triple - daily
1999 Triumph Tiger 885i - fun and free

the slow heart

Why exactly OEM gauge, you could easily improvise with another pressure gauge reading max at least 5 Bar.

Pump voltage also, the el.socket is not super tight, so two thin wires could be put in the female orifices before plugging the socket, then use these two for your volt meter.

Have to check was there an easy way to clear long term trims.

Flyingwombat

Quote from: the slow heart on April 16, 2024, 11:34:15 AMWhy exactly OEM gauge, you could easily improvise with another pressure gauge reading max at least 5 Bar.

Exactly what I did in the end.

Pump voltage also, the el.socket is not super tight, so two thin wires could be put in the female orifices before plugging the socket, then use these two for your volt meter.

Have to check was there an easy way to clear long term trims.

So the pressure seems good, basically at 3 bar(g) consistently, even when it runs up the revs or stalls.

I have managed to find the number which changes LTFT to 3.0 (slider error still unresolved), much closer to 0 than -60.

So what I am seeing now.
At LTFT around 0 it fails turns over but doesn't rev to idle.
At LTFT around -10 it will remain stable but burning rich and smelly throttle response is slow to opening or closing.
At LTFT around -30 the application of the throttle will cause it to run up through the revs, even when throttle released.

So either burning rich or not at all. The opposite problem of previous lean burning.

I'm starting to think major vacuum leak from somewhere. Partly because if I manually cover the IACV to restrict air flow at idle it's still pulling air in from somewhere... Also looking at the throttle body vacuum it's far lower than it was when I last tried balancing it.

Potentially it's a throttle body gasket? Or maybe something else...

Still to replace injector seals, they arrived today.

2011 Triumph Street Triple - daily
1999 Triumph Tiger 885i - fun and free

the slow heart

Waiting injector seals replacement to rule them out.
Do you have lambda on the exhaust? Which map is on board now?

Flyingwombat

So when I took apart the injectors this time I noticed damage to a seal. Replaced all seals, they slid in much easier this time during assembly.

Assessed current situation.

Adjustments : IACV set to 120, Idle fuel trim @ 16.4, Long term fuel trim @ +3

Engine starting is difficult with failing to rev, when it does start it revs to approximately 1200 RPM before cutting out.


Map is 9892, Yes Lambda sensor is there.

For good measure, and because it is easy I am going to re-check my spark plugs to see if they've fouled since put in.
2011 Triumph Street Triple - daily
1999 Triumph Tiger 885i - fun and free

Flyingwombat

#28
Also worth noting that the fuel rail pressure on priming is 2.8 bar (g) and this drops to 2.6 bar (g) over 5 mins when engine is off. Fuel pump is squealing slightly during priming, however when I start the engine it keeps pressure.

Also noted in the manual that the cutting out could be a stuck IACV, which it is not, or a blocked throttle body 1 way valve... so I will look into that too.
2011 Triumph Street Triple - daily
1999 Triumph Tiger 885i - fun and free

Flyingwombat

Replaced fuel pump and hoses for good measure. Squealing has stopped, and the fuel pump reaches pressure faster. It started making a gushing sound when ignition is turned, I sent an inspection camera into the tank and it appears to be coming from the fuel pressure regulator, which I guess is how it works.

I also cannot find any 1 way valve between the throttle bodies and the IACV... I have blown down the IACV pipes, through the IACV housing too in order to check for blockages, all seems OK.
2011 Triumph Street Triple - daily
1999 Triumph Tiger 885i - fun and free