There has been a lot of talk of an imminent EU directive to introduce 10% ethanol into our fuels here in the UK. Should that pass is there any significant changes that need to be made to carb rubber components including manifold that needs to take place. I know in some african countries I have lived in the change was facilitated by moving from a black rubber compound to a red rubber compound to prevent component deterioration in high alcohol content fuels.
i.e. are your gaskets, diagaphrams, o-rings etc the same compound as ours presently?
we been running 10% ethanol for quite a few years and I have only seen brown crud form in the float bowls , and the fuel goes lame after a month or so of standing idle .
I have seen no damage to any rubber orings or gaskets or manifolds on any of my 4 tiggers , just that crappy brown shit that ends up in the float bowls over time .
Thats good to know. Imagine the hassle/cost of changing o-rings/rubbers etc!
Thanks Mustang.
You can look forward to this, though:
(https://lh6.googleusercontent.com/-Hpf8D3k20Wo/UOiJcEJlE2I/AAAAAAAAB3A/5ukBO-vHCIU/s705/IMG_3149.JPG)
Ethanol in the gas leaches through the plastic and will slowly separate your paint from your tank.
it aint the ethanol that causes that ...............................
some tanks were not prepped so good in the beginning .
it's the plastic tank in general that causes that , as the nylon ages it shrinks and the paint doesn't .
Quote from: Mustang on April 24, 2013, 10:59:41 PM
it aint the ethanol that causes that ...............................
some tanks were not prepped so good in the beginning .
it's the plastic tank in general that causes that , as the nylon ages it shrinks and the paint doesn't .
Interesting... I've had bubbles happen on dirtbike tanks under stickers, and always figured it was EtOH or something offgassing through the plastic. Good to know that it won't happen again if I repaint it!
Quote from: Rallyroo on April 25, 2013, 12:36:53 AM
Quote from: Mustang on April 24, 2013, 10:59:41 PM
it aint the ethanol that causes that ...............................
some tanks were not prepped so good in the beginning .
it's the plastic tank in general that causes that , as the nylon ages it shrinks and the paint doesn't .
Interesting... I've had bubbles happen on dirtbike tanks under stickers, and always figured it was EtOH or something offgassing through the plastic. Good to know that it won't happen again if I repaint it!
well for awhile anyway. :hat10
I'll be using bedliner. If it gets ratty again, I'll just reshoot it! :hat10
I'd support Mustang on this in as much I believe (but stand to correction) it is / was illegal for a manufacturer in the UK to sell a bike with anything other than a metal tank. It was the first thing I noticed on arriving here, all the XR's offroaders etc with metal tanks.... half stove in. How Hinkley bypassed that I do not know, but the reason behind the ban was fuel leaching through plastic. I surmise Hinkley tanks do not leach fuel. Some one please correct me if I'm wrong on that tidbit of info.
They all do sooner or later, I'm told by one who does know that's why all the "plastic" tanks, including the factory ones out in the East have stickers rather than paint. The guys who make Safari tasks on Australia told me I could paint if I wanted but it would blister eventually regardless of the fuel used.
Sealing the tank could be the answer? I'm going to try this to cure two leaking threads?
http://www.ebay.co.uk/itm/3M-776-SCOTCH-CLAD-1-LITRE-PROTECTIVE-COATING-TANK-SEALER-/161004081717?pt=UK_Body_Shop_Supplies_Paint&hash=item257c975235
Phase separation when the weather turns cold and you end up with water at the bottom of your tank. Drain about a pint of the tank every once in a while depending how long the bike stays outside.