I need new rear brake pads (not now, right now) and am loath to go to the nearest Triumph dealer, who is not really near anyway. Do any of the other OEMs (honyamakawzuki) use the same pads?
either order online, or get a more local dealer to order these for you
EBC - FA215/2 (normal) or FA215/2HH (Sintered)
or
Ferodo FDB631
Going price for makes like EBC HH is about £26 (Posted) currently.
Quote from: Sin_Tiger on May 17, 2015, 11:51:51 AM
Going price for makes like EBC HH is about £26 (Posted) currently.
Thanks for that. EBC pads here (depending on the type) go for anything between $34 and $45 a pair. I'll hurry off to the local motorcycle emporium and order some. A word to the wise. Check your pads and do not let them reach this state!! :augie
EBC pads, $50 delivered by Expresspost. Job done.
Now I have to slap myself for letting the others get to that horrible worn state!
Note to self: check fronts too.
Were they both like that? the rear caliper, on Girlies anyway, seizes more easily than the fronts and then wears one pad more than the other.
Quote from: Bixxer Bob on May 18, 2015, 11:57:08 AM
Were they both like that?
No, just one side. The other was well past its 'best by' date but had not quite reached the metal. I am going to strip the pistons out of the caliper while I am waiting for the pads just to be sure that all is well internally.
Love the back brake on these things. Use it all the time and it always feels strong and reassuring. Will even lock up if used too robustly. Pity the front isn't so good. Feels really wooden even after bleeding/changing fluid.
Quote from: nickjtc on May 18, 2015, 06:06:03 PM
No, just one side. The other was well past its 'best by' date but had not quite reached the metal. I am going to strip the pistons out of the caliper while I am waiting for the pads just to be sure that all is well internally.
If the pads don't wear more or less evenly, it's the slide pins that need attention. Carefully peel back the rubber boots and separate the two halves of the caliper. Remove the old grease, clean the pin and rubber boots and regrease before re-assembly. I use rubber-friendly red grease on them.
Quote from: Bixxer Bob on May 19, 2015, 11:46:39 PM
If the pads don't wear more or less evenly, it's the slide pins that need attention. Carefully peel back the rubber boots and separate the two halves of the caliper. Remove the old grease, clean the pin and rubber boots and regrease before re-assembly. I use rubber-friendly red grease on them.
Alrighty. Thanks for that.
I bought a set of stainless pins, for both front and back.
Well worth doing imho.
Quote from: rf9rider on May 20, 2015, 02:13:06 AM
I bought a set of stainless pins, for both front and back.
Where did you get them from?
Ebay i think, if not, Sprint Manufacturing used to do them.
Quote from: rf9rider on May 20, 2015, 12:59:34 PM
Ebay i think, if not, Sprint Manufacturing used to do them.
Yup they still do, you have to do a search as they are not categorised correctly. You can also get stainless pistons, pad pins, bleed nipples and hose clamp bolts.
These calipers don't split, make sure you dig All the old grease out of the dead end guide. Change the rubbers, is not worth cleaning them just to replace them in a few months.
And again, thanks. I'll be interested in seeing what shape the innards are in.
New pads finally arrived... so much for 'Express' post. Stripped the caliper and found that one of the two pistons was sticking mightily due to an accumulation of mung in the bore. Cleaned everything out, re-greased everything, re-assembled and replaced/bled the questionable looking brake fluid. It was only 18 months old but looked like it had been in the system for years.
All in all a straight forward job and it only took about an hour.
On my Legend, I used red rubber grease and new piston seals. I also polished the pistons on a fine wire wheel and cleaned out the caliper bodies really well. Using the red rubber grease absolutely transformed the performance of the brakes on that bike, and I am going to do the same thing on the Tiger. Sounds trivial really, but that red rubber grease is amazing! Also very difficult to find here in the states, as no auto parts store seems to carry it. I got it on ebay.
Quote from: ssevy on May 30, 2015, 06:52:10 PM
Also very difficult to find here in the states, as no auto parts store seems to carry it. I got it on ebay.
Interesting. I got mine at the local big box place, aka Crappy tire. Readily available.