The book did not work when adjusting the chain, weird...

[Basri...]

After i get my new '97 Tiger, 750 km back home of course with helmet on and did not hear anything from the chain at all because of the earplugs and the helmet.

Next morning, riding to work, noices from chain and read the chain alignment part of the manuel 4 times, memorized it for having a first chain dirive bike after several BMWs...

As it mentioned in many topics here, book says, bike on SİDE or CENTER stand (does not say wheel of the ground), slack should be vertically 35-40mm.

Measured my slack, was abot 100-110mm, adjusted like the book says, but this time other weird noices from the chain and bike lost power...

Than i adjusted it wheel of the ground to 35-40mm, it was even worst...

Than i did the last thing i wanted to do, went to a mechanic, he wanted me to sit on the bike and he adjusted the chain while i am sitting on the bike to about 50-60mm slack, than it is perfect...

Than which is wrong ?

Manuel or my chain ?

[Mustang]

measure 20 links of chain in several spots , you should have 12.5 inches (317.5 mm)of length for 20 links . you probably have worn spots in your chain that will effect adjustment ie tight ,loose ,tight ,loose

with a new chain the best way I have found is to sit on the bike and get chain adjusted so it has approx 45 mm slack
now get off the bike and see what you have for slack when it is on the side stand . now you have a reference to go by with the bike on side stand .


understand ?

[Basri...]

understand ?

Yes, thanks...

[Basri...]

After reading ALL posts here about the chain, i urgently need new rub block + rub strip .

My rub block worn out to the bottom...

So, there is no way i can adjust the chain which also need to be repleced in the future, chain is not very bad for the moment.

Today is my day off and going to make a teflon rub block if i can, which will work until i get the proper ones.

Here in Turkey there is no way at all to find Triumph parts. That's why, is there anybody could give me a link of a dealer, can deliver to Turkey & i can pay with credit card (in U.K or E.U., not in U.S.A. or Canada) where i can get rub block + rub strip for my '97 Tiger...

Many thanks in advance...

[Basri...]

Here is my worn rub block;


This is my interim home made teflon rub block;


I had to shave the top of teflon block about 15mm to fit the chain between block and strip


Than went to a friend makes graphics, my tank is not blank any more;


Than removed the not working Triumph clock, installed a Voltmeter instead (12V when ignition on, 14V when running, i think this is good)


All processes took 3 hrs of my day off, now i can clean my baby and go for a ride.. :D

Still need recomendations for where i can get rub block and rub strip as i mentioned on above post...

[rf9rider]

These deliver anywhere.

http://www.worldoftriumph.com/ (http://www.worldoftriumph.com/)

[Basri...]

Thank you rf9rider, just ordered them, 41 GBP including shipping (shipping 11 GBP)

I think takes about 7-10 days to receive...

[R0B]

I like the voltmeter. Probably a much better addition than a clock. I might have to have a look for a suitable unit and do the same.......

Looks in excellent condition with 70k on the clock!!

[Basri...]

I like the voltmeter. I might have to have a look for a suitable unit and do the same.......

Check the marine equipment stores, the ones they sell are waterproof..

[MtheTiger]

I like the voltmeter.

+1

[Basri...]

Friday received the rub block and the strip from http://www.worldoftriumph.com/ (http://www.worldoftriumph.com/) rf9rider, thank you for the link .

Removing the old strip and replacing the new one seemed difficult to me, i think will change it with professional help.

But removed the home made teflon rub block and installed the original OEM one.

What a change...

O.k. it does not last very long but not big money, except emergency, i will never put the teflon one back, always will get an OEM one...

[Mustang]

Removing the old strip and replacing the new one seemed difficult to me, i think will change it with professional help.

http://tigertriple.com/forum/index.php/topic,5260 (http://tigertriple.com/forum/index.php/topic,5260)
it's not that bad of a job

[Basri...]

http://tigertriple.com/forum/index.php/topic,5260 (http://tigertriple.com/forum/index.php/topic,5260)
it's not that bad of a job

Thanks, this is encouraging..

Will try next Sunday, will get dark soon here, 7 hrs ahead from N.Y. and 11 hrs ahead of CA.. :D

[Basri...]

Could not wait till next Sunday, thanks to TigerTriple and thanks to Mustang finished the job 2 hrs ago. That was 1 hour work but had to remove the new rub block i've just put on today..  







Yes Mustang,  it is a real tight fit

Pushed it to the house with an iron bar and hammer, glad that did not demage the rubber strip... Yours looked easier.

7. Stick the new one in and use something with a blunt end to tap it home , it;s a tight fit,

[theclowncrusty]

Hi Mustang, ( i jus tknow you will be the one answering this question!)

What should the distance between the lower chain rub block and the swinging arm be? As i have had to make a bracket to fit my new rub block, i am not sure if i welded it in exactley the right place? I have about 15-20 mm of movement that i can choose where to tighten the bolt up. (Hope this makes sense.)
Crusty